Cooper Bussmann Power Module PS User Manual download pdf

8-29-01

XXXXXX

Bussmann

Power Module

™

Switch PS

All-In-One Module

Form No. PS

Page 1 of 5

BIF Doc# 1145

Bussmann

Power Module™ Switch

Standard Features:

• 30-400 amp 600 Vac 3p Fused Power Switch

• 200,000 amp RMS Short-Circuit Current Rating

• Shunt trip 120V

• Control power terminal block

• Ground lug per NEC

• Class J fuse mounting only

Optional Features:

• Control power transformer with fuses and blocks

• Fire safety interface relay

• Key to test switch

• Pilot light – “ON”

• Isolated neutral lug

• Mechanically interlocked auxiliary contact for hydraulic

elevators with battery backup (5 amp 120 Vac rated)

• Fire Alarm Voltage Monitoring Relay (To monitor Shunt Trip

Voltage)

• NEMA 3R, 4, and 12 enclosures available

• Phase failure and undervoltage relay available, consult

factory

• For added protection, use the Bussmann SAMI fuse

covers to improve maintenance personnel protection

(OSHA 1910.333, paragraph C)

Agency Information:

U.L. 98 Enclosed and Dead Front Switch

Guide 96NK3917, File E182262

NEMA 1, U.L. 50, listed enclosure

cU.L. per Canadian Standards C22.2, No. 0-M91-CAN/CSA

C22.2, No. 4-M89 Enclosed Switch

Power Module™ Switch

Rating (Amps) Power Module Switch Catalog No.

30 PS3

60 PS6

100 PS1

200 PS2

400 PS4

Optional Accessories

Catalog

Rating Number

Option 1

Control Power Transformer 208V T20

(CPT) Std. 100VA with PRI & 240V T24

SEC Fuse (120V Secondary) 480V T48

600V T60

Option 2

Fire Safety Interface 24 Vdc Coil R2

Relay (3PDT, 10 amp, 120V) 120 Vac Coil R1

Option 3

Key to Test Switch 120V K

Option 4

Pilot Light – “ON” Red R

Green G

White W

Option 5

Isolated Neutral Lug 30-60A N6

(Full Capacity)

100A N1

200A N2

400A N4

Option 6

Mechanically interlocked auxiliary contact 1 NO & 1 NC A

for hydraulic elevators with automatic

recall (5 amp 120 Vac rated)

Option 7

Fire Alarm Voltage Monitoring Relay Single-Pole F1

(To monitor Shunt Trip Voltage) Three-Pole F3

Option 8

Optional Enclosure NEMA 3R U

NEMA 4 Y

NEMA 12 Z

Catalog No. Construction: Catalog number of PS Switch

Options as required in option order as listed above

(i.e. option 1, 2, 3, etc.)

Example: • 100A S.T. Switch 480V-3P – PS1

• 480–120V CPT – T48

• 120 Vac Coil Fire Safety Interface Relay – R1

• Pilot Light - “ON” (Green) – G

• Mech. Interlock (1 NO & 1 NC) – A

Catalog Number PS1T48R1GA

Class J fuses not included.

Oversized 200% rated neutral option available where required by excessive

non-linear loads.

Through 200A.

Through 100A.

Options 1,2,& 6 are standard for elevator circuits.

Bussmann

How to configure Part Numbers:

Step 1: Select Switch Amperage

Step 2: Select Options Needed

1 2 3 4 5

Summary of Contents

Page 1 - Switch PS

8-29-01XXXXXXBussmann®Power Module™Switch PSAll-In-One ModuleForm No. PSPage 1 of 5BIF Doc# 1145Bussmann® Power Module™ SwitchStandard Features:• 30-4

Page 2

Bussmann®Power Module™Switch PSAll-In-One ModuleForm No. PS Page 2 of 5BIF Doc# 1145Standard Shunt Trip RatingsAmp Max Max1Mom

Page 3 - Switch PS

Bussmann®Power Module™Switch PSAll-In-One ModuleForm No. PS Page 3 of 5BIF Doc# 1145Typical Control with Wiring Options for Fire Safety Interface (O

Page 4

Bussmann®Bussmann®Power Module™Switch PSAll-In-One ModuleLegend:N.O.F.A. – Normally Open Fire Alarm contacts supplied from the fire alarm system to

Page 5

Bussmann®Power Module™Switch PSAll-In-One ModuleForm No. PS Page 5 of 5BIF Doc# 1145Section 16XXX – Power Module Switch(Elevator) (Computer Room) (E

Comments to this Manuals

No comments

Cooper Bussmann Power Module PS User Manual

Browse online or download User Manual for Fire protection Cooper Bussmann Power Module PS. Cooper Bussmann Power Module PS User's Manual

Summary of Contents

Comments to this Manuals